File Name: 1233X20.EXE Title: Compaq PageMarq Lotus 1-2-3 for DOS Release 3.1 & 3.4 Driver Version: 2.0 Instructions Version: 09/12/94 CATEGORY: Driver EFFECTIVE DATE: 02/08/94 PRODUCTS AFFECTED: PageMarq 15 and PageMarq 20 laser printers OPERATING SYSTEM: MS-DOS SYSTEM CONFIGURATION: Lotus 1-2-3 for DOS Release 3.1 & 3.4 SUPERSEDES: SP0486 DESCRIPTION: This release contains the printer drivers for the Compaq PageMarq 15 and 20 laser printers using Lotus 1-2-3 for DOS Release 3.1 & 3.4. The Softpaq contains the self-extracting archive named 1233X20.EXE. To use the driver, you must first extract it using the following steps: 1. Execute the Softpaq in any empty directory. 2. Make that directory current. 3. Execute 1233X20.EXE. TABLE OF CONTENTS: ======================================================== I.....General Information about PageMarq WYSIWYG drivers II....Installation Instructions for Update Disk III...Printing The SP0931.DOC File ======================================================== =============================================================== (I) GENERAL INFORMATION ABOUT PAGEMARQ WYSIWYG DRIVERS =============================================================== The driver provides spreadsheet and graphic printing the PostScript mode of the Compaq PageMarq 15/20 printers. Features supported include: * Lempel-Ziv-Welch Compression filter. * Level II Postscript command for Paper and Tray selection * Use of Policies dictionary. PAPER TRAY HANDLING Paper tray selection works using the principle of tray PRIORITIES. If several trays contain like sized paper, they will be searched for a non-empty tray in an order which depends on the tray selected in the WYSIWYG configuration (:Print Config Bin). The tray selections work as follows: TRAY ORDER IN WHICH TRAYS ARE SEARCHED Upper Upper Lower MPF Lower Lower Upper MPF Single MPF only (uses MPF irrespective of page size) Manual Manual Feed only (should be used only if no MPF is installed) Reset Uses the printer control panel default ====================================================== (II) INSTALLATION NOTES FOR UPDATE DISK ====================================================== NOTE: If you run 1-2-3 from a network drive, your network administrator must install the Update on your server. Network administrators need full access rights to install the Update. The installation procedure below is the same for stand-alone users and for network administrators. To use the Update Disk, you must complete these steps: 1. Place the Compaq PageMarq Driver disk in drive A: 2. Change to drive A: by typing A: then 3. Type INSTDRV "path" "drive": Substitute your 123 directory for "path", and the drive letter of the distribution disk for "drive". For help, just type: INSTDRV 4. Change to your 123 directory (INSTDRV will give instructions). The Introductory Lotus Install screen should now appear. Press 5. Select "Change selected equipment" then press 6. Select "Modify current DCF" then press 7. Select "Change selected printer" then press 8. Select "Compaq" then press 9. Select "PageMarq 15/20" then press 10. Select the appropriate entry for the size of paper you wish to use (i.e. Letter or A4) and press 11. If you wish to use Letter and A4, repeat steps 7 - 10 for the unselected paper size 12. Select "Return to Menu" and press 13. Select "Return to Main Menu" and press 14. Select "End Install Program" and press 15. Choose "Yes" to save changes and press 16. Press to use 123 as the DCF name 17. Choose "Yes" to end install and press The selected driver and font combinations will now be installed and can be used in Lotus 123 Release 3.1 or 3.4 =================================================================== (III) PRINTING THE SP0931.DOC FILE =================================================================== NOTE: PRINTING SP0931.DOC TO A LOCALLY CONNECTED PRINTER 1. Make the drive that contains the Update Disk current. 2. At the DOS prompt, enter the following command: PRINT SP0931.DOC PRN (Where PRN represents the port you print to for example LPT1, LPT2, LPT3, or PRN) For more information on printing a file from DOS, please consult your DOS manual. NOTE: PRINTING SP0931.DOC TO A NETWORK PRINTER 1. Make the drive that contains the Update Disk current. 2. At the DOS prompt, enter the following command: COPY SP0931.DOC LPTX (Where X represents the port you print to for example LPT1, LPT2, LPT3, or LPT4) For more information on printing a file from DOS, please consult your DOS manual. For more information on determining your network printer port, please contact your network administrator. ================================================================== The Update contained on this diskette is licensed by Lotus Development Corporation, solely for the use by Licensed Users of 1-2-3 for DOS Releases 3.1 and 3.4. (C)opyright 1992, 1993 Lotus Development Corporation. All Rights Reserved. LOTUS DEVELOPMENT CORPORATION MAKES NO WARRANTIES, EITHER EXPRESS OR IMPLIED REGARDING THE ENCLOSED, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THERE MAY BE OTHER RIGHTS THAT YOU MAY HAVE WHICH VARY FROM STATE TO STATE. LOTUS DEVELOPMENT CORPORATION EXCLUDES ANY WARRANTY COVERAGE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. Lotus (R) and 1-2-3 (R) are registered trademarks of Lotus Development Corporation.