[MicroStation 4.0 PC]

  There is one additional step needed to complete the MicroStation PC 4.0
  Driver Installation.  You need to reboot the system before running 
  USTATION.BAT from the \USTAT40 subdirectory.

  So the installation steps will be:

	1. ...     
	2. ...
	3. ...
	4. ...
	5. Run the USCONFIG program to select the new device driver.
	   a.  ...
	   b.  ...
		. 
		. 
		. 
	   f. Select, "Exit and Save".

  Add -->     Reboot the system.

	   g. Run USTATION.BAT from the \USTAT40 subdirectory.
	   h.  ... 
	   i.  ... 



[OS/2 2.1, 2.11, and 3.0]

*************************************************************************
NOTE:
     
     1. The refresh rate utility program is replaced by OS2REFSH.EXE.

     2. This program can be used to change refresh rate under OS/2 2.1,
	2.11, and 3.0 (WARP) for Windows.

     3. Please run this program at DOS Command Prompt (full screen).
	After changing the new refresh rates, you need to shutdown and 
	reboot system for the changes to take effect.

*************************************************************************
 
Installation Instructions for OS/2 2.1, 2.11, and 3.0 (WARP) for Windows:

Installation Considerations
     
     1.  The installation process assumes that the user knows the  
	 maximum vertical refresh rate as well as the maximum   
	 resolution of the monitor.
     
     2.  When installing the S3 driver over a non-S3 driver 
	 (e.g., SVGA), the standard IBM VGA driver must be      
	 installed first.  This is not required if an S3 driver   
	 is already installed.
     
     3.  The S3 driver will not install unless an S3 chip-based 
	 card is installed in the machine at the time of driver      
	 installation. 
     
     
Installation Instructions
     
     1.  Make sure you have all open data files saved before 
	 continuing the S3 driver installation.
  
     2.  Make sure Win-OS/2 session and all Seamless Windows 
	 applications are closed. (Seamless applications are 
	 windows applications that run on top of the PM Desktop.)
     
     3.  Open an OS/2 command prompt (windowed or full screen).
     
     4.  Insert driver diskette into the floppy drive. 
     
     5.  Change to the floppy drive (A: or B:) into which you have 
	 inserted VideoBlitz III AV Utility Programs disk #2. Verify that the
	 diskette is labeled "S3 DRV1" (do the same for disk #3). If it is not
	 labeled then type "label S3 DRV1" or "label S3 DRV2".
     
     6.  Type S3INST A: C: and press "Enter".  ("A" is the floppy 
	 drive; "C" is the drive OS/2 is installed).
     
	 Note: You may see an error message stating could not locate files. 
	 Please ignore this message.
     
     7.  When prompted, insert VideoBlitz III AV Utility Programs disk #3. 
	 (It must be labeled "S3 DRV2".)
     
     8.  When prompted, exit the OS/2 command prompt, remove floppy
	 disk from drive, and shutdown and reboot system.
 
     9.  When OS/2 is up insert disk 'S3 DRV1' into the floppy drive.
     
     10. Double click on the the "OS/2 System" icon.
     
     11. Double click on the "System Setup" icon.
     
     12. Double click on the "Display Driver Install" icon. 
     
     13. When prompted by the Display Driver Install dialog, select
	 Primary Display and then click the OK button.
     
     14. Select the "32 Bit S3 Display Drivers" option from the 
	 Primary Display Adapter Type dialog and click the OK 
	 button.
     
     15. Select the appropriate option from the Monitor 
	 Configuration/Selection Utility dialog, and click the 
	 OK button.  Select "Default" if it is an S3 BIOS that was not      
	 modified by the OEM.
     
	 THE SCREEN WILL TEMPORARILY FLASH AND GO BLACK.  PLEASE 
	 WAIT FOR THE SOURCE DIRECTORY DIALOG TO APPEAR.
     
     16. The Source Directory dialog will be displayed.  Set the source     
	 directory to the location of disk 'S3 DRV1'.  Double click 
	 on the "Install" button.
     
     17. Insert disk 'S3 DRV2' into the floppy drive when prompted.
 
     18. The Installation Program may pause and display prompts to 
	 overwrite certain files.  Please answer YES for each file.
     
     19. You will be given a message stating that you "Must 
	 Shutdown and Restart your system for the changes to take 
	 effect".  Click the OK button.
     
     20. Remove driver diskette from the floppy drive.  
     
     21. Shut down and reboot system.  
     
	Note:  You can double click the "System" Icon in the System Setup  
	to change resolution before shutting down.
     
	After you reboot your system will come up with your newly 
	installed driver.
     
     To Change Resolution:

     22. To switch resolutions, double click on the "System" icon  
	 in the System Setup Folder.

     23. Highlight the resolution and close the dialog.

     24. Shut down and reboot.