CMD CSA-6460U2 software drivers release version 2.00
----------------------------------------------------

			Welcome to CMD UltraIDE   
		      -------------------------

  This README file contains important information about CSA-6460U2 
  CMD Ultra IDE Controller.  For the latest information about CMD 
  Ultra IDE controller, please read this file in its entirety.

  CONTENTS
  --------
  
  I. INSTALLING CSA6460U2 CONTROLLER
  II. DRIVER DESCRIPTION
  III. DRIVER INSTALLATION
  IV.  "INSTALL" PROGRAM


I. INSTALLING CSA6460U2 CONTROLLER
-----------------------------------
Please follow procedure on "CSA-6460U2 Bus Master PCI to Ultra-Enhanced 
IDE Controller Installation Guide."

CAUTIONS:
1. Don't insert CSA-6460U2 controller until told to do so in the 
instructions for Windows 95, OSR2, and Windows 98.

2. Make sure that the jumpers on the drives are set correctly for Master 
and Slave configuration.

3. Insert the CSA-6460U2 into a PCI slot that supports bus master DMA. 
Refer to your motherboard manual to identify the bus-master PCI slots.

4. Clear your CMOS drive(s) configuration to "NONE" or "AUTO" after
the CSA-6460U2 is inserted to system if onboard IDE controller is not
used.  If an onboard IDE controller and CSA-6460U2 are used together, 
then only hard drives connected to onboard IDE controller 
should be configured in CMOS.  To make it simple, set them to "auto" in
CMOS.



II. DRIVER DESCRIPTION
---------------------

  This is the general release of CMD CSA-6460U2 Ultra IDE drivers. 
  This release includes the following drivers :

  - DOS driver 
    CMD646x2.sys V2.24 June 4, 1998
    CMD646x.sys  V2.24 June 4, 1998
    CMDATPCD.SYS V1.14 February 12, 1998

  - Windows 95 driver
    CSA64XX.MPD  V1.3.4 May 13, 1998

  - Windows NT3.5x/4.x driver 
    CSA64XX.SYS  V1.2.2 April 14, 1998


III. DRIVER INSTALLATION
-------------------------

  Software Drivers:
     DOS	         : see DOS\README.DOS
     Windows 95/OSR2/98  : see WIN95\README.TXT
     Windows NT 3.5x/4.0 : see WINNT\README.NT

***************************************************************
For Windows 95/OSR2/98, please read Installation Guide or
README.TXT in WIN95.  Users need to load driver first before 
inserting CMD CSA-646U2 controller card into system.
***************************************************************

DOS
----
  DOS files are in the DOS\ directory.  See DOS\README.DOS for 
  instruction.

Windows 95
----------
  Windows 95 files are in the WIN95\ directory.  See 
  WIN95\README.TXT for instructions.

Windows NT
----------
  NT3.5x/4.x files are in the WINNT\ directory.
  See WINNT\REAME.NT for instructions.

IV.  "INSTALL" PROGRAM
-------------------------
  "INSTALL" program will automatically install CMD cdrom driver 
  (CMDATPCD.SYS).  This driver will be necessary when users want 
  to use a CDROM under DOS/Windows3.xx and 'command prompt only 
  mode' under Windows 95/OSR2/98.  Cdrom driver from cdrom 
  manufacturer will not work with CSA-6460U2 controller unless it 
  is written to support native mode (using different IRQ for IDE 
  controller besides IRQ14 and IRQ15) besides legacy mode. 
  
  Type the path where your installation program resides.  For 
  instance, if you will be installing from drive A, type:

    A:INSTALL
  
  It creates /quickcmd directory, copies cmdatpcd.sys file into
  the /quickcmd directory, and modify config.sys and autoexec.bat.
  Restart system then users will be able to use CDROM under DOS/
  Windows3.xx and 'command prompt only mode' under 
  Windows 95/OSR2/98.