<<<<<<<<< NEWS RELEASE FROM PME ENGINEERING >>>>>>>>>> * Thanks for the great responses during our 1994 Year-End SALE, here is a list of our 1995 new product lines and pricing. ** We now use ((SHARP 6N139)) chip in most of our MIDI module, the best you- can-get opto-isolator for MIDI purpose. >>>>>> <> Minimum required input current: PC900V- 4 mA, 6N138- 1.6 mA, 6N139- 0.5 mA. Prevent voltage incompatibility problem among different manufacturers, the SHARP 6N139 IC takes the load off your input MIDI device. <<<<<<<< * We'll soon be adding graphics and sounds to our WWW site, please check it. PME Engineering - electronic music technologies - - serving INTERNET since 1991 - Basic Computer Music Hardware for Soundcard >Product Line 1: PME MIDI Adaptor for soundcard: Works for SB, PAS, GUS, Azteck, Reveal,Packard Bell, Roland, Aria, Turtle Beach, Ensoniq, Logitech, all model with 15 pin SB compatible MIDI/game port connector. Compatible with all your original soundcard software and driver in Win/DOS for MIDI in/out function. Option 1 - !! BEST SELLING KIT !! (part#PME-k01) All parts and PCB, Game port pass-thru included, instructions ............ $14 This kit includes 1 buffer IC, 1 high speed opto-isolator , 2 IC sockets, Printed Circuit Board, 2"x3", solder masked, drilled, ready to solder, 5' long cable to soundcard game port, 15 pin D-SUB plug, with plastic hood and screws, 1 female D-SUB 15 pin socket for your joystick. 2 female MIDI jacks, 2 LED indicators: 1 green LED for displaying MIDI in activities, 1 red LED for displaying out activities. There is provision on PCB for MIDI Thru capability. The kit has no enclosure for your maximum MIDI project flexibility. (Uses SHARP 6N139, newest opto-isolator for MIDI input) Option 2 - !! BEST SELLING MIDI BOX !! (part#PME-c01) Fully Assembled MIDI Adaptor for Soundcard ............................... $20 Uses same parts as Option 1, but less game port pass-thru socket,fully assembled in a 3"x4"x1.2" high-impact plastic box(blue) with LED's on the top panel, and MIDI in/out sockets in the front , comes with 1 year warranty against defect. Sturdy design. Our BEST SELLING MIDI adaptor for all soundcard !! (Uses SHARP 6N139, newest opto-isolator for MIDI input) Option 3 - !! BEST SELLING FULL FEATURED BOX !! (part#PME-c02) Fully Assembled MIDI Adaptor for Soundcard w/ Game pass-thru, MIDI thru... $26 Same as Option 2 , Plus game port pass-thru, a female 15 pin socket for your joystick to plug in. MIDI in/out/thru 3 jacks, 2 LED's, warranty. (Uses SHARP 6N139 newest opto-isolator for MIDI input) Option 4 - (part#PME-c03) SB style MIDI adaptor cable, with game port pass-thru ....................$22 2 patch cables 4' long with MIDI plugs(male) for MIDI in and MIDI out, the other end of MIDI cables are 15 pin D-SUB plugs(male) to the soundcard game port,and 15 pin D-SUB socket (female) for your joystick. (Uses SHARP PC-900V opto-isolator chip) > MIDI Accessories Line (part#PME-p01) or (part#PME-p02) Professional MIDI cables ...........................$5 each or $9 one pair 6 foot long, elegant ivory color, fully foil shielded for safe use in computer EMI environment without MIDI data loss. (part#PME-t01) MIDI TESTER, a nice device for MIDI diagnostic ........................... $5 With MIDI socket(female), and LED on top for checking MIDI signals, just plug in immediately diagnose MIDI stream, System Exclusive and data compatible. WINDOWS USERS, your low-cost ticket to WIN-MIDI world! > Product Line 2: (part#PME-i01) WIN-MIDI interface card for PC (8 bit card) .............................. $39 Most of the sequencer software todays runs fast and does not dependent on MPU-401 smart mode anymore, especially if you run software in Windows, this is the best MIDI interface card for Windows, MPU-401 UART mode compatible. Comes with Windows drivers for Windows 3.0 or above, easy configuration. If you want to do MIDI programming in Windows/DOS, this is the must have card, software on 3.5" disk. These are for Electronic Music Hobbyist! > Product Line 3: (part#PME-m01) MIDI Merger Box, 2 MIDI in/ 1 MIDI out ................................... $59 Comes with AC adaptor, microprocessor on-board running at 12 Mhz. System Exclusive message compatible, has overflow LED indicator. Low cost solution to merge your two MIDI signals into one. For Musicians, take your board to gigs! >Product Line 4: (part#PME-DBDS1) DBDS-1 daughter board Docking Station ................................... $79 works for SB Waveblaster, Ensoniq DB, Roland SCD-10/SCD-15, tested, or any daughterboard with 26-pin Waveblaster compatible header type connector. Complete with ABS enclosure(ivory), AC-plug power, board enable logic, reset button, stereo output and MIDI in/out sockets, also MIDI LED indicator. Instantly turn your existing Daughterboard into a GS/GM external sound module. ---------- Ordering Information ----------------- ** Shipping and handlng is $4 standard for U.S., $6 for Canada. $9 for international air parcel post. We can't accept VISA yet, but will accept COD order through e-mail or phone/fax,add $4.50 COD fee. We ship in 1-2 business days after we get the order. ** International orders, email for detailed transaction method, the shipping and handling is US$9, by air, We have experience shipping to Asia, Austria, Australia,Netherland. It takes one week for most countries. ** Now a disk full of MIDI song files is FREE with order, at your request. ** Indiana Resident please add 5% State Sales Tax. Send check/MO (Canadian Postal Money Order is O.K.) to: PME Engineering P.O. Box 3134 West Lafayette, IN 47906-0583 U.S.A. E-mail: PME@holonet.net (Preferred)(Questions, Product Info, Payment Method) Phone/Fax: (317) 743-1734 World Wide Web URL: http://www.holonet.net/pme