############################################################################# # # # CD-ROM (for ATAPI) Installation Manual # # (c) PIONEER ELECTORONIC CORP. # # # ############################################################################# 1. Connecting the CD-ROM Drive 1.1 Adding the CD-ROM Drive to a configuration with one IDE Hard Disk Set CD-ROM Drive to SL(Slave mode) by setting a jumper on the rear side. Make sure the Hard Disk is set to IDE Master mode(Check your Hard Disk's documentation for details). 1.2 CD-ROM Drive only connection to IDE card MA(Master mode) or SL(Slave mode) are both valid settings. 2. Setting on each OS 2.1 MS-DOS If your OS is MS-DOS ( or IBM PC-DOS) , then perform the following steps : 2.1.1 Installation with setup program Execute SETUP.EXE which is in the attached Floppy disk. You can copy the device driver to install directory and rewrite CONFIG.SYS and AUTOEXEC.BAT with SETUP.EXE. If you don't use the installation program, then perform the following steps : 2.1.2 Copy from Floppy disk Copy the file ATAPI_CD.SYS to your Hard disk. 2.1.3 Modify CONFIG.SYS After Connecting the CD-ROM Drive and copying the device driver to the Hard Disk, add the following line to CONFIG.SYS : DEVICE=C:\ATAPI_CD.SYS LASTDRIVE=Z Valid options for this device driver are listed below. In most cases however, you don't need to specify any options. In case no options are specified, the driver will search for the CD-ROM Drive automatically. If the device driver loads successfully but the CD-ROM Drive can't be accessed, you must specify the LASTDRIVE line in CONFIG.SYS. Setting device driver options : e.g. : DEVICE=C:\ATAPI_CD.SYS /S:1 /D:MSCD001 [Option] /S:x ------> CD-ROM Drive ID. This determines the setting of the drive to Master or Slave and the connection to the Primary or Secondary IDE channel. x = 0: Master Drive on Primary IDE Channel 1: Slave Drive on Primary IDE Channel 2: Master Drive on Secondary IDE Channel 3: Slave Drive on Secondary IDE Channel /D: ******* --> CD-ROM Device name e.g.: /D:PIONEER If you do not specify this option, a default CD-ROM Device name is used : "MSCD001". In case you copied the device driver to a sub-directory, specify the FULL PATH name in the "DEVICE=..... " line in CONFIG.SYS. 2.1.4 Modify AUTOEXEC.BAT Add the following line to AUTOEXEC.BAT. e.g. : MSCDEX.EXE /D:PIONEER Make sure the CD-ROM Device name is same as in CONFIG.SYS : "/D:PIONEER". (In case you didn't specify this option in CONFIG.SYS, specify : "/D:MSCD001") 2.2 MS-Windows Ver3.xx (Ver 3.1,Ver 3.11,for Workgroup) In case the CD-ROM Drive is connected to the Primary IDE Channel and the IDE Hard Disk is set to Master mode, the 32bitDiskAccess parameter in the Windows SYSTEM.INI file should set to OFF. This can be achieved in two ways : Double-click Control Panels, then double-click 386Enhanced and uncheck the 32bitDiskAccess checkbox. Click OK and restart. Experienced users can edit the SYSTEM.INI file in the Windows directory : 32bitDiskAccess=OFF 2.3 Windows NT (Upper Ver3.5) After connecting the CD-ROM Drive to the primary IDE Channel in Slave mode, install Windows NT. then the CD-ROM Drive will be automatically recognised. If you are adding the CD-ROM Drive to an existing Windows NT installation, refer to the Windows NT documentation. (The CD-ROM Drive can be installed as ATAPI device) 2.4 OS/2 Warp (Upper Ver3.0) After connecting the CD-ROM Drive to the primary IDE Channel in Slave mode, install OS/2 Warp and choose "Other IDE CD-ROM" from the CD-ROM Device list. 2.5. Windows95 After connecting the CD-ROM Drive to the primary or secondary IDE channel, and then you should refer to the section 2.1 and install the (MS-)DOS device driver (ATAPI_CD.SYS). If you are adding the CD-ROM Drive to an existing Windows95, the CD-ROM Drive can be automatically recognized. Copying & distribution of this device driver is prohibited. PIONEER ELECTRONIC CORPORATION ------------------------------------------------------------------------ PIONEER ELECTRONIC (EUROPE) N.V. MULTIMEDIA DIVISION OPTICAL SYSTEM DEPARTMENT PIONEER HOUSE, HOLLYBUSH HILL, STOKE POGES, SLOUGH SL2 4QP, UK TEL: +44 (0) 1753 789789 FAX: +44 (0) 1753 789880 E-MAIL: optical@pioneer-eur.com URL: http://www.pioneer-eur.com/ ------------------------------------------------------------------------ PIONEER NEW MEDIA TECHNOLOGIES,INCD TECHNICAL SUPPORT DIVISION 2265 E.220TH STREET,LONG BEACH, CA 90810 USA TEL: +1 (310)-952-2111 FAX: +1 (310)-952-3031 BBS: +1 (310)-835-7980 URL: http://www.pioneerusa.com/ ------------------------------------------------------------------------ PIONEER ELECTRONICS MARKETING(ASIA) CO. INDUSTRIAL BUSINESS DIVISION 501 ORCHARD ROAD, #10-00 WHEELOCK PLACE, SINGAPORE 238880 TEL: +65-735-9011 FAX: +65-734-1732 E-MAIL: pacibd@pioneer.com.sg URL: http://www.pioneer.com.sg/ ------------------------------------------------------------------------