3200 (250-1633) Settings Faxback Doc. # 2830 The following are the jumper and switch settings for the 3200: Jumper Default Setting Optional Setting Function E1 1-2 (IRQ 7) 2-3 (IRQ 5) LPT1 E2 Off (33/66 MHz) 1-2 (25/50 MHz) Microprocessor Speed E3 On (Enabled) Off (Disabled) Built-In Video E4 Off (Disabled) On (Enabled) Monochrome Video (Requires seperate video adapter and E3 must be disabled) E5 Off (Enabled) On (Disabled) Password Microprocessor E6 E7 E8 E9 E10 Type Pins Pins Pins Pins Pins 80487SX 1-2 1-2 2-3 1-2 2-3 80486DX 1-2 1-2 1-2 2-3 2-3 80486DX2/ODPR 1-2 1-2 1-2 2-3 2-3 OverDrive* 1-2 1-2 2-3 1-2 2-3 Pentium 2-3 1-2 2-3 1-2 2-3 OverDrive* * This system uses only 5-volt OverDrive and Pentium OverDrive microprocessors. Additional Jumpers Default Optional Setting Function E11 Connected Disconnected Computer Reset Button E12 Connected Disconnected Power-On LED E13 Disconnected Disconnected Connector for Optional Speaker E14 Enabled Disabled Game Port (Must cut wire to disable) By default, the computer's built-in parallel port responds as LPT1 and uses IRQ7. IF you install an add-on board with a parallel port configured to memory address 03BCh, you need to adjust jumper E1 on the system board so the built-in parallel port will operate as LPT2 and use IRQ5. To change the IRQ setting to IRQ5: 1. Locate the IRQ jumper E1 on the system board (see the illustration on the back flap of this manual). 2. By default, the jumper is set to IRQ7 (pins 1 and 2). Move the jumper block to pins 2 and 3 to set the parallel port to IRQ5. 3. Replace the computer-chassis cover. Reconnect peripheral devices and plug in the power cord. Turn on the system. 4. If there is a memory-address conflict between the add-in parallel port and the built-in parallel port, run System Setup. Use the Parallel Port field in the Ports menu to set a new memory address for the built-in parallel port. SETTING VIDEO AND GAME PORT JUMPERS The system board contains jumpers that you can use to configure your computer's display mode and enable or disable the game port (for jumper locations, see the illustration in the layout document). The system is set so you can connect your monitor to the built-in VGA connector. The system will also recognize most add-in video adapters, should you prefer to use one. Disable the built-in VGA only if you install an add-in adapter and the system does not recognize it. To disable the built-in VGA, locate jumper E3 on the system board. Then, move the jumper block from pins 1 and 2 only. If you have disabled the built-in VGA connector and intend to install a monochrome, rather than color, display adapter as the primary video adapter, you must set jumper E4. Locate jumper E4 on the system board and set the jumper block on pins 1 and 2. The back panel of your system includes a game port connector. If you install an add-in board that includes a game port, use jumper E14 to disable the built-in game port. To disable the built-in game port, locate jumper E14 on the system board. Then move the jumper block from pins 1 and 2 to pin 2 only. To disable the built-in game port, locate jumper E14 on the system board. Then move the jumper block from pins 1 and 2 to pin 2 only. To re-enable the built-in game port, move the jumper block from pin 2 to pins 1 and 2. (SMC/jej/jjs-11/04/94)