JP 250 (26-2873) IBM Control Codes Faxback Doc. # 4136 The control code functions supported in IBM X24E are summarized below. Summary of Control Codes: Dec. Hex. Mnemonic Function 0 00 NUL Command terminator 7 07 BEL Beeper 8 08 BS Backspace 9 09 HT Horizontal Tab 10 0A LF Line Feed 11 0B VT Vertical Tab 12 0C FF Form Feed 13 0D CR Carriage Return 14 0E SO Select One-Line Double-Width Mode 15 0F SI Select Condensed Mode 17 11 DC1 Select Printer 18 12 DC2 Select 10 CPI 19 13 DC3 Deselect Printer 20 14 DC4 Cancel One-Line Double-Width Mode 24 18 CAN Cancel Line 27 1B ESC Escape sequences 32 20 SP Space Escape (ESC) Sequences: Dec. Hex. Mnemonic Function 27 45 n 1B 2D n ESC - n Underlining 27 48 1B 30 ESC 0 Set 1/8" Line Spacing 27 49 1B 31 ESC 1 Set 7/72" Line Spacing 27 50 1B 32 ESC 2 Start Line Spacing Set by ESC A 27 51 n 1B 33 n ESC 3 n Set Graphics Line Spacing 27 52 1B 34 ESC 4 Set Top of Form 27 53 n 1B 35 n ESC 5 n Automatic Line Feed 27 54 1B 36 ESC 6 Select IBM Set 2 27 55 1B 37 ESC 7 Select IBM Set 1 27 58 1B 3A ESC : Select 12 Pitch 27 61 n1 n2 1B 3D n1 n2 ESC = n1 n2 24-dot font image download 27 65 n 1B 41 n ESC A n Set Text Line Spacing 27 66 n1..0 1B 42 n...00 ESC B n...0 Set Vertical Tabs 27 67 n 1B 43 n ESC C n Set Form Length in Lines 27 67 0 n 1B 43 00 n ESC C NUL n Set Form Length in Inches 27 68 n1...n0 1B 44 n1...n0 ESC D n...00 Set Horizontal Tabs 27 69 1B 45 ESC E Select Emphasized Mode 27 70 1B 46 ESC F Cancel Emphasized Mode 27 71 1B 47 ESC G Select Double-Strike Mode 27 72 1B 48 ESC H Cancel Double-Strike Mode 27 73 n 1B 49 n ESC I n Select Print Mode 27 74 n 1B 4A n ESC J n Execute Graphics Line Feed 27 75 n1 n2 1B 4B n1 n2 ESC k n1 n2 Select Normal-Density Graphics 27 76 n1 n2 1B 4C n1 n2 ESC L n1 n2 Select Double-Density Graphics 27 78 n 1B 4E n ESC N n Set Skip Over Perforation 27 79 1B 4F ESC O Cancel Skip Over Perforation 27 80 n 1B 50 n ESC P n Proportional Mode 27 81 3 1B 51 03 ESC Q 3 Deselect Printer 27 82 1B 52 ESC R Set All Tabs to Default Setting 27 83 n 1B 53 n ESC S n Select Super/Subscript Mode 27 84 1B 54 ESC T Cancel Super/Subscript Mode 27 85 n 1B 55 n ESC U n Unidirectional Printing Mode 27 87 n 1B 57 n ESC W n Double-Width Mode 27 88 n1 n2 1B 58 n1 n2 ESC X n1 n2 Set Left and Right Margins 27 89 n1 n2 1B 59 n1 n2 ESC Y n1 n2 Double-Density image graphics 27 90 n1 n2 1B 5A n1 n2 ESC Z n1 n2 Quadruple-Density image graphics 27 91 64 1B 5B 40 ESC [ @ n1 Set presentation highlight n1 n2 n1 n2 n2 27 91 75 n1 n2 1B 5B 4B n1 n2 ESC [ K n1 n2 Initialize Printer 27 91 84 n1 n2 1B 5B 54 n1 n2 ESC [ T n1 n2 Set code page 27 91 92 n1 n2 1B 5B 5C n1 n2 ESC [ \ n1 n2 Change graphics line spacing 27 91 103 n1 n2 1B 5B 67 n1 n2 ESC [ g n1 n2 High resolution graphics 27 92 n1 n2 1B 5C n1 n2 ESC \ n1 n2 Print Continuously from All Characters Chart 27 94 n 1B 5E n ESC ^ n Print Single Character from All Characters Chart 27 95 n 1B 5F n ESC _ n Overscoring 27 100 n1 n2 1B 64 n1 n2 ESC d n1 n2 Relative move inline forward 27 106 1B 6A ESC j Go offline 27 51 n 1B 33 n ESC 3 n Set graphics line spacing (AGM) 27 65 n 1B 41 n ESC A n Set text line spacing (AGM) 27 74 n 1B 74 n ESC J n Graphics line spacing (AGM) 27 42 m n1 n2 1B 42 m n1 n2 ESC * m n1 n2 Select graphics mode (AGM) Note: The n or m indicates a parameter that features the control code functions. AGM means alternate graphics mode. Emulation Restrictions of IBM Mode: The IBM Mode emulation of this printer has a few restrictions, described below, because of hardware differences. If you make programs for the printer in IBM Mode, pay special attention to these restrictions. The reverse feed code ESC ] is not supported. The styles of block graphics characters at 12 cpi are different. With the Auto Sheet Feeder (26-2884) attached, the printer might skip the last two lines on a page.This only becomes a problem when you direct the output of some DOS command to the printer (e.g. "dir > prn"), and the text on the page exceeds the number of printable lines (64). (jej 04/26/94)