LP 1000 (260-2804) IBM Control Codes Faxback Doc. # 4727 The following table shows codes in IBM emulation mode. __________________________________________________________________________ HEX |DEC |ASCII |FUNCTION _____:______:____________:________________________________________________ 00 |00 |NUL |Terminator. _____:______:____________:________________________________________________ 07 |07 |BEL |Ignored. _____:______|____________|________________________________________________ 08 |08 |BS |Backspace. _____|______|____________|________________________________________________ 09 |09 |HT |Horizontal tab. _____|______|____________|________________________________________________ 0A |10 |LF |Line feed. _____|______|____________|________________________________________________ 0B |11 |VT |Vertical tab. _____|______|____________:________________________________________________ 0C |12 |FF |Form feed. _____|______|____________|________________________________________________ 0D |13 |CR |Carriage return. _____|______|____________|________________________________________________ 0E |14 |SO |Enter double-width print mode. _____|______|____________|________________________________________________ 0F |15 |SI |Select condensed (16.7 CPI) Character | | |spacing. _____|______|____________|________________________________________________ 11 |17 |DC1 |Select printer. _____|______|____________|________________________________________________ 12 |18 |DC2 |Select 10 CPI Character spacing (default). _____|______|____________|________________________________________________ 13 :19 |DC3 |Ignored. _____|______|____________|________________________________________________ 14 |20 |DC4 :End double-width print mode. _____|______|____________|________________________________________________ 18 |24 |CAN |Cancel data. _____|______|____________|________________________________________________ 1B |27 |ESC BEL |Ignored. 07 | 07 | | _____|______|____________|________________________________________________ 1B |27 |ESC BS |Backspace (same as BS). 08 | 08 | | _____|______|____________|________________________________________________ 1B |27 |ESC HT |Horizontal tab (Same as HT). 09 | 09 | | _____|______|____________|________________________________________________ 1B |27 |ESC LF |Line feed (same as LF). 0A | 10 | | _____|______|____________|________________________________________________ 1B |27 |ESC VT |Vertical tab (same as VT). 0B | 11 | | _____|______|____________|________________________________________________ 1B |27 |ESC FF |Form feed (Same as FF). 0C | 12 | | _____|______|____________|________________________________________________ 1B |27 |ESC CR |Carriage return (Same as CR). 0D | 13 | : _____:______:____________:________________________________________________ 1B |27 |ESC SO |Enter double-width print mode (same as SO). OE | 14 | | _____|______|____________|________________________________________________ 1B |27 |ESC SI |Select condensed (16.7 CPI) character spacing 0F | 15 | |(same as SO). _____|______|____________|________________________________________________ 1B |27 |ESC DC1 |Select printer (same as DC1). 11 | 17 | | _____|______|____________|________________________________________________ 1B |27 |ESC DC2 |Select 10 CPI character spacing (default; same 12 | 18 | |as DC2). _____:______:____________:________________________________________________ 1B |27 |ESC DC3 |Ignored (same as DC3). 13 | 19 | | _____|______|____________|________________________________________________ 1B |27 |ESC DC4 |End double-width print mode (same as DC4). 14 | 20 | | _____|______|____________|________________________________________________ 1B |27 |ESC CAN |Cancel data (same as CAN). 18 | 24 | | _____|______|____________|________________________________________________ 1B |27 |ESC ! |Return to Tandy mode. 21 | 33 | | _____|______|____________|________________________________________________ 1B |27 |ESC - n |Begin/end underlining. 2D | 45 | | n = 0: End underlining n | n | | 1: Begin underlining | | | Default = Off _____|______|____________|________________________________________________ 1B |27 |ESC 0 |Set 1 /8" line feed. 30 | 48 | | _____|______|____________|________________________________________________ 1B |27 |ESC 1 |Set 7/72", line feed. 31 | 49 | | _____|______|____________|________________________________________________ 1B |27 |ESC 2 |Execute ESC A setting. 32 | 50 | | _____|______|____________|________________________________________________ 1B |27 |ESC 3 n |Change line feed distance to n/216". 33 | 51 | | 1