Logitech C7 Mouse (260-1199)            Setup          Faxback Doc. # 5447

BACK UP YOUR LOGITECH MOUSE DISKETTE

We recommend that you put write-protect tabs on the diskette for the 
LOGITECH C7 Mouse Standard Package before performing the DISKCOPY command.

If you are using a dual floppy disk computer:

1. Insert your DOS diskette in drive a. At the A> prompt, type:

    DISKCOPY A: B: [ENTER]

NOTE: to Zenith users: Zenith recommends use of the VERIFY option with the
DISKCOPY command, thus:

    DISKCOPY A: B: /V [ENTER]

2. Follow the instructions on the screen. Insert your LOGITECH C7 Mouse
   Standard Package (source) diskette in drive A, and a blank (target)
   diskette in drive B. Press [ENTER].

   If you are using one floppy disk and a hard disk:

   1. At the DOS A> prompt or C> prompt, type:

      DISKCOPY A: A: [ENTER]

   2. Follow the instructions on your screen. The source is your LOGITECH C7
      Mouse Standard Package diskette, and the target is a blank diskette.

MTRACK, THE MOUSE TEST PROGRAM

The MTRACK Test Program is on the LOGITECH C7 Mouse Standard Package
diskette. It tells you:

* Whether your mouse is connected to COM1 or COM2.

* Whether your mouse is working electrically.

* Whether the mouse buttons are working.

It is especially important to run MTRACK when you use your mouse for the
first time. To run MTRACK:

1. Dual Floppy Disk Users: Switch the computer ON. Insert your DOS disk in
   drive A and bring up the A> prompt. then remove the DOS disk.

   Hard Disk Users: Switch the computer on and bring up your DOS prompt.

2. With the LOGITECH C7 Mouse Standard Package diskette in drive A, type:

    A: [ENTER]
    A:MTRACK [ENTER]

   You'll see the welcome message for MTRACK.

3. Press [F1] to determine whether your mouse is connected to COM1 or COM2.

   In most cases, you will be at COM1. If not, press [F2]. When you have
   identified the correct serial port, MTRACK will display the port name at
   the bottom of the screen. You'll also see Button Status, which should
   read:

    Up Up Up.

4. Press the mouse buttons. Observe the Button Status display as you press
   each mouse button. The corresponding Up changes to Down.

5. Move the mouse and observe the screen. The cursor should move as you move
   the mouse.

6. To exit MTRACK, press [ESC].

LOGITECH C7 MOUSE (26-1199) (9-pin)  SOFTWARE INSTALLATION

These instructions tell how to install your software onto either a floppy
drive or hard disk system. Instructions on screen tell you how to proceed.

IF YOU ARE USING A DUAL FLOPPY DISK COMPUTER:

1. At the A> prompt insert the LOGITECH C7 Mouse Standard disk into drive A
   and type:

    INSTALL [ENTER]

2. A prompt asks you to identify your disk system. Type:

    A:FLOPPY [ENTER]

3. Read the rest of the information on the screen and follow the
   instructions.

IF YOU ARE USING ONE FLOPPY DISK AND A HARD DISK DRIVE:

1. At you DOS prompt, insert the LOGITECH C7 Mouse Standard Package diskette
   in drive A and type:

    A:INSTALL [ENTER]

2. A prompt asks you to identify your disk system. Type:

    A:HARD [ENTER]

3. Read the rest of the information on the screen and follow the
   instructions.

NOTE: Consult the READ.ME files for information about which files are
installed and which directories are used.

TIME-SAVING AUTOEXEC.BAT COMMANDS

When your installation is complete, you may want to add some commands to
your AUTOEXEC.BAT file is DOS to automatically load the mouse driver and
the menu driver each time you start the computer. (Refer to your MS-DOS or
PC-DOS manual for instructions on creating or modifying an AUTOEXEC.BAT
file.) Make the following additions to your AUTOEXEC.BAT file.

IF YOU ARE USING COM1             IF YOU ARE USING COM2

    MOUSE                         MOUSE 2
    MENU                          MENU
    CLICK                         CLICK

(dkh-07/30/93)