Model 129 (160-0829) Power Source Faxback Doc. # 6296 You can power the camcorder from any of three sources: The AC adapter/charger, the battery, or your vehicle battery. Using the AC ADAPTER/CHARGER 1. Connect one end of the power cord to the AC adapter/charger's DC OUT jack. 2. Connect the other end of the power cord to the camcorder's DC IN 6V jack. 3. Plug the AC adapter/charger's power cord into an AC outlet. You can now operate the camcorder. Caution: The supplied AC adapter/charger is specially designed for use with the Model 129 camcorder. Never use it to power any other device. USING THE BATTERY You can power the camcorder using the supplied battery. You must charge the battery before you use it. Charging the Battery Caution: Use only the suppled AC adapter/charger or optional vehicle adapter/charger to charge the battery. Use of any other adapter/charger could damage the battery. Also, do not use the supplied AC adapter/charger to charge any battery except the type supplied. To Charge the battery, do the following: 1. Align the battery's alignment mark with the adapter/charger's alignment mark. 2. Gently press the battery against the adapter/charger, and slide the battery to the right until it locks in place. 3. Plug the AC adapter/charger's power cord into an AC outlet. The green indicator lights. The adapter/charger's CHARGE indicator lights and charging begins. When the battery is fully charged, the CHARGE indicator lights red. Notes: It takes about 130 minutes to fully charge the battery. The exact charging time depends on the ambient temperature and the condition of the battery. 4. When charging is complete, remove the battery from the adapter/ charger by sliding the battery to the left; then disconnect the adapter/charger from the wall outlet. Battery Status Indicators When the battery is fully charged, E- -F appears in the viewfinder. The two bars between E and F indicate the remaining battery power. As the battery's power is used, the bars disappear one at a time. When only one bar appears, battery power is low. When the battery's power gets lower, BATTERY appears in the viewfinder. The indicator next to the power switch flashes, and in a few seconds the camcorder automatically turns off. Recharge the battery or power the camcorder from the supplied AC adapter or the optional DC adapter. You can order additional batteries from your local Radio Shack store so you can use one battery while charging another. Attaching the Battery to the Camcorder 1. Align the battery's alignment mark with the camcorder's alignment mark. 2. Gently press the battery against the camcorder, and slide the battery to the right until it clicks into position. Removing the Battery from the Camcorder 1. Turn off the camcorder. 2. Push and hold down BATTERY EJECT, and slide the battery to the left. Note: Always stop the tape and turn off the camcorder before you remove the battery. The tape remains wound around the video head during recording or playback. You might damage the tape if you remove the battery during recording or playback. Battery Usage Hints Recording with many starts and stops, frequent zooming, and recording in low temperatures might shorten actual recording times. Be sure to turn the power off when not recording. We recommend you prepare an extra battery so you do not have to interrupt your recording. Do not use an insufficiently charged or discharged battery. Use of such batteries might cause the power to automatically stop during camcorder operation, possibly damaging the tape, battery, and camcorder. The camcorder consumes a small amount of battery power even when the camcorder's power is off. If you are not going to use the camcorder for a while, remove the battery before storing it. The camcorder consumes a small amount of battery power even when the camcorder's power is off. If you are not going to use the camcorder for a while, remove the battery before storing it. Extending Battery Life Recharge the battery immediately after the recording session is over. Leaving the battery uncharged can irreparably damage the battery, preventing further recharging or use. Recharge the battery again right before recording. A battery stored for an extended time loses some power, resulting in decreased recording time. Recharge the battery at least once every 6 months even when the battery is not used. Store the battery in a dry, cool place. Replacing the Battery While Recording 1. If BATTERY flashes in the viewfinder during recording, press REC START/STOP to stop recording. Then turn off the power. Do not press STOP. Note: Be sure the power indicator is off before you remove the battery. 2. Replace the battery with a charged one. 3. Turn on the power. || PAUSE appears in the viewfinder and then changes to ||---- 4. Press REC START/STOP to continue recording from the same place as before. USING A VEHICLE ADAPTER/CHARGER Caution: Use this procedure only if your vehicle has a 12-volt negative- ground electrical system. Use only the recommended vehicle adapter/-charger (CMC No. 16-2304). To power the camcorder using the vehicle adapter/charger, do the following: 1. Connect one end of the power cord to the vehicle adapter/charger's DC OUT jack. 2. Connect the other end of the power cord to the camcorder's DC IN 6V jack. 3. Plug the vehicle adapter/charger's power cord into your vehicle's cigarette-lighter socket. You can now operate the camcorder as usual. Cautions: The recommended vehicle adapter/charger is specially designed for use with the Model 129 camcorder. Never use it to power any other device. When you unplug the camcorder, remove the vehicle adapter/ charger from the cigarette-lighter socket first, then unplug the power cord from the camcorder. Notes: Be sure to push the plug completely into the cigarette-lighter socket. Be sure the socket is free from ashes and other debris. (BR/all-07/13/94)