Wireless Home Control (610-2610) Installation Faxback Doc. # 6544 This section describes how to initialize all of the system's accessories so they are recognized by the console and how to test the system to make sure it is working properly. You must also follow the appropriate initialization and testing procedures in this section to add other separately purchased accessories to the system. SETTING UP THE CONSOLE 1. Choose a location for the console. Its location should be: Close to a telephone jack so you can easily connect the telephone dialer. Central to the door/windows you want to protect so all sensors are within range of the console (100 feet). Positioned where you can easily check the zone indicators for any problems but not where an intruder could easily see it. 2. Set the house and unit code dials on the console to A1. Note: You can set the console to any house code, but you must also set all accessories/sensors to the same house code. 3. Place a 9-volt alkaline battery (Radio Shack Cat. No. 23-553) in the battery compartment for backup power in case there is an AC power failure. Note: Be sure to install the backup battery. If there is no battery and the console loses AC power, you must re- initialize all of the system's accessories. 4. Plug the console into any AC outlet that is not controlled by an on/off switch and fully extend the antenna. 5. Plug the telephone cord into the console and plug the other end into a modular phone jack. Notes: If you do not have an unused jack, use the supplied duplex adapter. For a baseboard jack, plug the adapter into the jack; for a wall jack, plug the adapter into the console. If you do not have a modular phone jack, you can either update the wiring yourself or have the phone company do it for you. Radio Shack stores sell the jacks and adapters you need. The USOC number of the jack to be installed is RJ11C for a baseboard jack or RJ11W for a wall jack. INSTALLING THE KEYCHAIN REMOTE CONTROL 1. Remove the screw from the back of the keychain remote control and open the cover. Install a 6V alkaline battery (Radio Shack Cat. No. 23-469) in the battery compartment, according to the polarity symbols (+ and -) marked inside. Then replace the cover and the screw. 2. Set the console's INSTALL/RUN 1/RUN 2 switch to INSTALL. 3. Stand near the console and press ARM on the remote control. The console chimes and logs in the remote control. If you do not hear a beep, or if the red light stays on, press CODE on the back of the remote control with a pencil point and then press ARM. 4. Leave the console's switch set to INSTALL to install other accessories. Notes: You can add any combination of plug 'n power remote controls up to a total of eight. The BATTERY indicator on the remote control lights when you press a button to show the battery is good. INSTALLING THE HANDHELD REMOTE CONTROL 1. Install four AAA alkaline batteries (Radio Shack Cat. No. 23-555) in the handheld remote control's battery compartment, following the polarity symbols (+ and -) marked inside the compartment. 2. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 3. Set the house code on the remote control to the same letter as the console. 4. Press ARM HOME or ARM AWAY on the handheld remote control. The console sounds a tone. If you do not hear a tone, press the button beneath the remote control's label with a pencil. Then repeat this step. 5. Leave the console's switch set to INSTALL to install other accessories Note: You can add any combination of plug 'n power remote control up to a total of eight. INSTALLING THE DOOR WINDOW SENSORS 1. Slide open a door/window sensor's battery compartment cover in the direction of the arrow. Install a 9-volt alkaline battery (Radio Shack Cat. No. 23-553) in the door/window sensor's battery compartment. Then replace the cover. 2. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 3. Stand near the console and press TEST on the sensor. The console chimes and logs in the door/window sensor. The first available zone indicator in the console lights. If you do not hear a chime, or if the sensor's red light stays on, press CODE with a pencil point and the press TEST. 4. Set the switch inside the door/window sensor's battery compartment to NC (normally closed) and the switch on the front of the sensor to MIN. 5. Place one of the supplied numbered stickers on the sensor to show its zone number. Repeat Steps 1-5 for additional door/window sensors. Leave the console's switch set to INSTALL to install other accessories. INSTALLING THE MOTION DETECTOR 1. Install a 9-volt alkaline battery (Radio Shack Cat. No. 23-553) inside the motion detector's battery compartment and replace the cover. 2. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 3. Press TEST on the back of the motion detector. The console beeps, and the first available zone indicator lights to show the console has logged in the motion detector. If you do not hear a chime, press CODE with a pencil. 4. Looking at the back of the motion detector, set the switch on the left side to 1 . Set the switch on the right side to HOME/AWAY. 5. Place one of the supplied numbered stickers on the motion detector to show its zone number. 6. Leave the console's switch set to INSTALL to install accessories. INSTALLING THE LAMP MODULE 1. Plug a lamp into the included lamp module and plug the module into an AC outlet that is on the same electrical circuit as the console. 2. Set the lamp module's house and unit code dials to the same letter and number as the console. TESTING THE SYSTEM After you have completed all of the quick installation procedures, follow these steps to test the system. 1. Set the INSTALL/RUN 1/RUN 2 switch on the console to RUN 2. The RECORD light stays on for 15 seconds. 2. Place each door/window sensor's magnet next to its magnetic switch. 3. Place the motion detector on a counter top within 100 feet of the console. 4. Move a door/window sensor's magnet away from magnetic switch. The console emits a chime sound. This happens every time someone opens a door or window in the RUN 2 mode if you have not armed the system (RUN 1 mode = no chimes). Replace the magnet next to the magnetic switch. 5. Press ARM on a remote control, and then move the magnet away from the magnetic switch again. The alarm sounds and the lamp connected to the lamp module flashes on and off. Press DISARM to turn off the alarm. Press LIGHTS OFF to turn off the lamp. Replace the magnet next to the magnetic switch. 6. Press ARM on the remote control, and then walk across the path of the motion detector's lens. The alarm sounds and the lamp connected to the lamp module flashes on and off. Press DISARM to turn off the alarm, and the console chimes twice. Press LIGHTS OFF to turn off the lamp. (LB/all-07/11/94)